Finetech Engineering is a Gelbo flex tester manufacturer that pharma, packaging and petrochemical-film labs in Gujarat buy from directly: manufacturer, not a trader, built at Wagle Estate, Thane. Our ASTM F392 flex durability tester shows whether a barrier film or laminate survives the twisting and creasing of converting, filling and transport.
What is the Gelbo flex test? A 200 × 280 mm specimen on two mandrels is twisted and crushed – 440° over the first 90 mm of stroke, then a 65 mm push – at 45 cycles per minute. What does a Gelbo flex tester measure? The damage. You then count pinholes (dye or coloured turpentine) or compare OTR with an unflexed control – a pinhole flex test for barrier films run on a flexible packaging film testing machine.
Gujarat is a major pharma and chemicals state, and its GIDC estates also house flexible packaging converters and film makers.
ASTM F392 conditions A to E explained: five conditions, set by cycle count at 45 cycles per minute.
| Condition | Flex type | Cycles | Time | Use case |
| A | Full flex (twist + crush) | 2,700 | 60 min | Most severe; clear-film seals can fail |
| B | Full flex | 900 | 20 min | Intermediate, per specification |
| C | Full flex | 270 | 6 min | Moderate; routine comparison |
| D | Full flex | 20 | about 27 s | Early-failure screen, e.g. delamination |
| E | Partial flex only | 20 | about 27 s | Gentlest, per specification |
How many cycles are in a Gelbo flex test? 2,700, 900, 270 or 20 full-flex cycles (A-D), or 20 partial (E). How long does a Gelbo flex test take? 60, 20 or 6 minutes of flexing for A-C, under half a minute for D or E, plus loading and the pinhole check. Can a Gelbo flex test run as a quick screen? Condition D (full flex) or E (partial flex) runs 20 cycles in about 27 seconds, plus loading and the pinhole check.
Note: Your specification or customer agreement sets the condition, not ASTM F392 itself. Condition moisture-sensitive films first, and always run an unflexed control.
Key technical data for the Gelbo flex tester dispatched to flexible packaging labs in Gujarat.
| Parameter | Specification |
| Testing Standard | ASTM F392 |
| Sample Dimensions | 200 mm × 280 mm (8 in × 11 in) |
| Twisting Frequency | 45 cycles per minute |
| Twisting Angle | 400° or 440° (model dependent) |
| Stroke / Compression Distance | 80 mm or 155 mm horizontal travel (model dependent) |
| Mandrel Diameter | 90 mm, stainless steel |
| Drive System / Motor | 1/2 HP, 1440 RPM gear motor with 45 rpm output, controlled by a Delta-make drive |
| Power Requirements | 230 V AC, 50 Hz |
| Dimensions (approx.) | 1000 mm (W) × 390 mm (D) × 340 mm (H) |
Twist angle and stroke depend on the model. Earlier we described a 440° twist over the first 90 mm followed by a 65 mm push, 155 mm in all; that is the 440° / 155 mm configuration.
Manufacturer, not a trader. A laboratory testing equipment manufacturer that labs in Gujarat deal with directly: built, calibrated and dispatched from Wagle Estate, Thane. We are a direct source for packaging film testing equipment that pharma and chemical labs in Gujarat need at the flex step.
Full and partial flex. Every ASTM F392 flex durability tester we ship to Gujarat runs Conditions A to E at 45 cycles per minute.
NABL traceable, ISO 9001:2015. Calibration certificates traceable to national standards; CE marked; direct factory supply.
One source for packaging QC lab equipment in Gujarat: Choosing between a Gelbo flex test and a dart impact test for packaging film? Run both – add our dart impact tester and humidity chamber.
Direct dispatch from Thane since 2023. Converters in Ahmedabad and Surat buy from us directly; we dispatch from Thane with installation, calibration and AMC. Orders from Sachin GIDC, Surat follow the same route.
See the full specifications on our main Gelbo flex tester page. We also supply and install Gelbo flex testers in other states: Gelbo flex tester in Andhra Pradesh · Gelbo flex tester in Karnataka · Gelbo flex tester in Maharashtra · Gelbo flex tester in Tamil Nadu · Gelbo flex tester in Telangana.
| Product | Why Related |
Impact puncture of films (ASTM D1709) |
|
Film tensile (ASTM D882) and seal strength (ASTM F88) |
|
Conditioning specimens before flexing |
|
Cutting film strips for tensile testing |
|
Flex cracking of rubber (ASTM D430) |
|
Cut growth of rubber soles (ASTM D1052) |
|
Flex endurance of thin rubber components |
|
Drop testing of filled pouches and cartons |
|
Transport simulation of packed goods |
All Equipments & specimen preparation products can be customised as per requirements.