Finetech Engineering is a Gelbo flex tester manufacturer that pharma and packaging labs in Telangana buy from directly: manufacturer, not a trader, built at Wagle Estate, Thane. Our ASTM F392 flex durability tester shows whether a barrier film or laminate survives the twisting and creasing of converting, filling and transport.
What is the Gelbo flex test? A 200 × 280 mm specimen on two mandrels is twisted and crushed – 440° over the first 90 mm of stroke, then a 65 mm push – at 45 cycles per minute. What does a Gelbo flex tester measure? The damage. You then count pinholes (dye or coloured turpentine) or compare OTR with an unflexed control – a pinhole flex test for barrier films run on a flexible packaging film testing machine.
Genome Valley and Patancheru anchor Hyderabad’s pharma manufacturing; strip packs, sachets and blister laminates depend on foil-laminate barrier integrity, and Conditions D and E give a quick check. Why does foil laminate barrier matter for strip pack shelf life? Foil keeps moisture and oxygen out, so a cracked barrier can shorten shelf life.
ASTM F392 conditions A to E explained: five conditions, set by cycle count.
| Condition | Flex type | Cycles | Time | Use case |
| A | Full flex (twist + crush) | 2,700 | 60 min | Most severe; clear-film seals can fail |
| B | Full flex | 900 | 20 min | Intermediate, per specification |
| C | Full flex | 270 | 6 min | Moderate; routine comparison |
| D | Full flex | 20 | about 27 s | Early-failure screen, e.g. delamination |
| E | Partial flex only | 20 | about 27 s | Gentlest, per specification |
How many cycles are in a Gelbo flex test? 2,700, 900, 270 or 20 full-flex cycles (A-D), or 20 partial (E). How long does a Gelbo flex test take? 60, 20 or 6 minutes of flexing for A-C, under half a minute for D or E, plus loading and the pinhole check. How do you decide which Gelbo flex test condition to run? Use the condition the specification names, or agree one first; ASTM F392 fixes none per material.
Key technical data for the Gelbo flex tester supplied to packaging labs in Telangana.
| Parameter | Specification |
| Testing Standard | ASTM F392 |
| Sample Dimensions | 200 mm × 280 mm (8 in × 11 in) |
| Twisting Frequency | 45 cycles per minute |
| Twisting Angle | 400° or 440° (model dependent) |
| Stroke / Compression Distance | 80 mm or 155 mm horizontal travel (model dependent) |
| Mandrel Diameter | 90 mm, stainless steel |
| Drive System / Motor | 1/2 HP, 1440 RPM gear motor with 45 rpm output, controlled by a Delta-make drive |
| Power Requirements | 230 V AC, 50 Hz |
| Dimensions (approx.) | 1000 mm (W) × 390 mm (D) × 340 mm (H) |
Both twist angle and stroke are model dependent; the motion described above (440° over the first 90 mm, then 65 mm straight, 155 mm in total) is the 440° / 155 mm model.
Manufacturer, not a trader. A laboratory testing equipment manufacturer that labs in Telangana deal with directly, including pharma packers who need barrier film testing equipment for the flex step.
Full and partial flex. Every ASTM F392 flex durability tester we ship to Telangana runs Conditions A to E.
NABL traceable, ISO 9001:2015. CE marked; direct factory supply.
One source for packaging QC lab equipment in Telangana: add our humidity chamber and dart impact tester. Pharma packaging QC labs in Patancheru can get all three quoted together.
Direct dispatch from Thane since 2023. Packers in Hyderabad and Secunderabad buy from us directly; we dispatch from Thane with installation and AMC. Pharma packaging labs in Genome Valley get the same Thane dispatch.
See the full specifications on our main Gelbo flex tester page. We also supply and install Gelbo flex testers in other states: Gelbo flex tester in Andhra Pradesh · Gelbo flex tester in Gujarat · Gelbo flex tester in Karnataka · Gelbo flex tester in Maharashtra · Gelbo flex tester in Tamil Nadu.
| Product | Why Related |
Impact puncture of films (ASTM D1709) |
|
Film tensile (ASTM D882) and seal strength (ASTM F88) |
|
Conditioning specimens before flexing |
|
Cutting film strips for tensile testing |
|
Flex cracking of rubber (ASTM D430) |
|
Cut growth of rubber soles (ASTM D1052) |
|
Flex endurance of thin rubber components |
|
Drop testing of filled pouches and cartons |
|
Transport simulation of packed goods |
All Equipments & specimen preparation products can be customised as per requirements.