Finetech Engineering

Gelbo Flex Tester Manufacturer in Maharashtra | Finetech Engineering

ISO 9001:2015 certified - Finetech Engineering
BIS standards compliant testing equipment - Finetech Engineering
20 years of experience in testing equipment - Finetech Engineering
100+ customers served - Finetech Engineering

Overview

Gelbo Flex Tester

Finetech Engineering is a Gelbo flex tester manufacturer that packaging labs in Maharashtra can buy from directly: manufacturer, not a trader, built at our Wagle Estate, Thane factory. Our ASTM F392 flex durability tester that converters in Maharashtra use shows whether a barrier film or laminate survives the twisting and creasing it meets in converting, filling and transport.

What is the Gelbo flex test? A 200 × 280 mm specimen is mounted on two mandrels that repeatedly twist and crush it – 440° of twist over the first 90 mm of stroke, then a straight 65 mm push – at 45 cycles per minute.

What does a Gelbo flex tester measure? The damage flexing causes. After conditioning you count pinholes (traced with dye or coloured turpentine on a white backing) or compare oxygen transmission rate with an unflexed control. That pairing is the pinhole flex test for barrier films, and it is why a flexible packaging film testing machine that converters in Maharashtra specify sits beside OTR equipment. How do you count pinholes after a flex test using the dye method? Apply the dye to the flexed area and count every stain that shows through.

Industries We Serve in Maharashtra

Maharashtra is a major flexible packaging hub; converters, pharma packers and FMCG brands want flex-durability data before approving a laminate.

ASTM F392 Conditions A to E - Which One for Your Film?

ASTM F392 conditions A to E explained: the standard defines five conditions, set by cycle count at 45 cycles per minute.

Condition Flex type Cycles Time Use case
A Full flex (twist + crush) 2,700 60 min Most severe; seal and structure worst-case screening
B Full flex 900 20 min Intermediate severity, per specification
C Full flex 270 6 min Moderate severity; routine comparison
D Full flex 20 about 27 s Early-failure screen, e.g. composite delamination
E Partial flex only 20 about 27 s Gentlest conditioning, per specification

How many cycles are in a Gelbo flex test? 2,700, 900, 270 or 20 full-flex cycles (A-D), or 20 partial-flex cycles (E). How long does a Gelbo flex test take? Flexing alone runs 60, 20 or 6 minutes for A, B and C, and under half a minute for D or E, plus specimen loading and the pinhole check. What is the difference between full flex and partial flex? A-D apply the full twist-and-crush motion, while E applies only part of it, as defined in ASTM F392.

Note: Does ASTM F392 specify condition per material? No: your material specification or customer agreement sets the condition, not ASTM F392 itself. Always run an unflexed control. Why run unflexed control sample with gelbo flex? It shows how much damage the flexing itself caused.

Gelbo Flex Tester Technical Specifications

Key technical data for the Gelbo flex tester built at our Wagle Estate, Thane factory and dispatched to Maharashtra labs.

Parameter Specification
Testing Standard ASTM F392
Sample Dimensions 200 mm × 280 mm (8 in × 11 in)
Twisting Frequency 45 cycles per minute
Twisting Angle 400° or 440° (model dependent)
Stroke / Compression Distance 80 mm or 155 mm horizontal travel (model dependent)
Mandrel Diameter 90 mm, stainless steel
Drive System / Motor 1/2 HP, 1440 RPM gear motor with 45 rpm output, controlled by a Delta-make drive
Power Requirements 230 V AC, 50 Hz
Dimensions (approx.) 1000 mm (W) × 390 mm (D) × 340 mm (H)

Twist angle and stroke depend on the model. The motion described above – 440° of twist over the first 90 mm, then a 65 mm push, 155 mm in all – is the 440° / 155 mm configuration.

Why Choose Finetech Gelbo Flex Tester in Maharashtra

Manufacturer, not a trader. A laboratory testing equipment manufacturer that labs in Maharashtra deal with directly: built, calibrated and dispatched from Wagle Estate, Thane. That also makes us a packaging film testing instruments manufacturer that converters in Maharashtra can buy from without a middleman.

Full and partial flex. Every ASTM F392 flex durability tester we ship to Maharashtra runs Conditions A to E at 45 cycles per minute.

NABL traceable, ISO 9001:2015. Calibration certificates traceable to national standards; CE marked equipment.

One source for packaging QC lab equipment that plants in Maharashtra need: add our dart impact tester, humidity chamber and vibration tester.

Local supply since 2023. Converters in Mumbai and Pune buy from us directly; we dispatch from Thane with installation, calibration and AMC.

See the full specifications on our main Gelbo flex tester page. We also supply and install Gelbo flex testers in other states: Gelbo flex tester in Andhra Pradesh · Gelbo flex tester in Gujarat · Gelbo flex tester in Karnataka · Gelbo flex tester in Tamil Nadu · Gelbo flex tester in Telangana.

Related Products
Product Why Related

Dart Impact Tester

Impact puncture of films (ASTM D1709)

Universal Testing Machine (UTM)

Film tensile (ASTM D882) and seal strength (ASTM F88)

Humidity Chamber

Conditioning specimens before flexing

Rectangle Cutter

Cutting film strips for tensile testing

Demattia Flex Tester

Flex cracking of rubber (ASTM D430)

Ross Flex Tester

Cut growth of rubber soles (ASTM D1052)

Bennewart Flex Tester

Flex endurance of thin rubber components

Drop Tester

Drop testing of filled pouches and cartons

Vibration Tester

Transport simulation of packed goods

Gelbo Flex Tester
Cadbury logo
Aditya Birla Group logo
ELGI Rubber logo
Nestlé logo
ITC Limited logo
Blue Star logo
Hindustan Unilever logo
Brahmins logo
Nirapara logo
Pidilite logo

Request a Free Quote

All Equipments & specimen preparation products can be customised as per requirements.

All Equipments and specimen preparation products can be customised as per requirements
Name
Email
Phone Number
Message
Common Questions

Frequently Asked Questions

It conditions barrier films and laminates by twisting and crushing them to ASTM F392, exposing pinholes, flex cracks and delamination. Our Gelbo flex tester units, paired with a pinhole count or OTR check, make a pinhole flex test for barrier films.
Follow your customer or pharma specification; the standard does not fix one per material (see ASTM F392 conditions A to E explained above). Foil laminates crack early, so a practical approach is a short Condition D or E to see early pinholes, then a longer condition for ranking.
Yes. We dispatch a Gelbo flex tester to labs in Mumbai from Thane, ready to commission, along with barrier film flex crack testing equipment for packers in Pune. Send your film structure and condition (A-E) and we confirm a configuration and quotation. Weighing a dealer against buying direct? We are the manufacturer, so there is no dealer in between.
For a Gelbo flex tester price in India, we quote against your conditions and specimen stations - no invented figures. Send your flexible packaging testing equipment requirement through the form or WhatsApp.
Gelbo flex repeats twisting and crushing to expose pinholes and flex cracks, a fatigue-type failure. Dart impact (ASTM D1709) drops a weight once to find the impact energy at which the film fails. In short, one tests fatigue failure and the other impact failure. We supply both as packaging QC lab equipment that plants in Maharashtra can order together.