Finetech Engineering is a Gelbo flex tester manufacturer that food, pharma and medical packaging labs in Karnataka buy from directly: manufacturer, not a trader, built at Wagle Estate, Thane. Our ASTM F392 flex durability tester shows whether a barrier film or laminate survives the twisting and creasing of converting, filling and transport. The Gelbo is the flex-durability piece of the food, pharma and medical packaging film testing equipment that labs in Karnataka assemble.
What is the Gelbo flex test? A 200 × 280 mm specimen on two mandrels is twisted and crushed – 440° over the first 90 mm of stroke, then a 65 mm push – at 45 cycles per minute. What does a Gelbo flex tester measure? The damage. You then count pinholes (dye or coloured turpentine) or compare OTR with an unflexed control – a pinhole flex test for barrier films run on a flexible packaging film testing machine.
Medical pouches, coffee sachets, dairy laminates and retort pouches all depend on barrier-film flex durability. Which films need a Gelbo flex test – food, pharma or medical? Any barrier film flexed in converting, filling or transport; the specification names the condition.
ASTM F392 conditions A to E explained: five conditions, set by cycle count.
| Condition | Flex type | Cycles | Time | Use case |
| A | Full flex (twist + crush) | 2,700 | 60 min | Most severe; clear-film seals can fail |
| B | Full flex | 900 | 20 min | Intermediate, per specification |
| C | Full flex | 270 | 6 min | Moderate; routine comparison |
| D | Full flex | 20 | about 27 s | Early-failure screen, e.g. delamination |
| E | Partial flex only | 20 | about 27 s | Gentlest, per specification |
How many cycles are in a Gelbo flex test? 2,700, 900, 270 or 20 full-flex cycles (A-D), or 20 partial (E). How long does a Gelbo flex test take? 60, 20 or 6 minutes of flexing for A-C, under half a minute for D or E, plus loading and the pinhole check.
Key technical data for the Gelbo flex tester dispatched to packaging labs in Karnataka.
| Parameter | Specification |
| Testing Standard | ASTM F392 |
| Sample Dimensions | 200 mm × 280 mm (8 in × 11 in) |
| Twisting Frequency | 45 cycles per minute |
| Twisting Angle | 400° or 440° (model dependent) |
| Stroke / Compression Distance | 80 mm or 155 mm horizontal travel (model dependent) |
| Mandrel Diameter | 90 mm, stainless steel |
| Drive System / Motor | 1/2 HP, 1440 RPM gear motor with 45 rpm output, controlled by a Delta-make drive |
| Power Requirements | 230 V AC, 50 Hz |
| Dimensions (approx.) | 1000 mm (W) × 390 mm (D) × 340 mm (H) |
The model decides the twist angle and stroke. The 440° twist, then 65 mm push (155 mm in all) described above is the 440° / 155 mm configuration.
Manufacturer, not a trader. A laboratory testing equipment manufacturer that labs in Karnataka deal with directly.
Full and partial flex. Every ASTM F392 flex durability tester we ship to Karnataka runs Conditions A to E.
NABL traceable, ISO 9001:2015. CE marked; direct factory supply.
One source for packaging QC lab equipment in Karnataka: add our humidity chamber and dart impact tester. As a Peenya Industrial Area packaging QC lab equipment supplier, we can quote all three in one go.
Direct dispatch from Thane since 2023. Packers in Bangalore and Mysore buy from us directly; we dispatch from Thane with installation and AMC. A Bommasandra medical device packaging film flex check starts with the same instrument.
See the full specifications on our main Gelbo flex tester page. We also supply and install Gelbo flex testers in other states: Gelbo flex tester in Andhra Pradesh · Gelbo flex tester in Gujarat · Gelbo flex tester in Maharashtra · Gelbo flex tester in Tamil Nadu · Gelbo flex tester in Telangana.
| Product | Why Related |
Impact puncture of films (ASTM D1709) |
|
Film tensile (ASTM D882) and seal strength (ASTM F88) |
|
Conditioning specimens before flexing |
|
Cutting film strips for tensile testing |
|
Flex cracking of rubber (ASTM D430) |
|
Cut growth of rubber soles (ASTM D1052) |
|
Flex endurance of thin rubber components |
|
Drop testing of filled pouches and cartons |
|
Transport simulation of packed goods |
All Equipments & specimen preparation products can be customised as per requirements.