Finetech Engineering is a Gelbo flex tester manufacturer that pharma and laminate labs in Andhra Pradesh buy from directly: manufacturer, not a trader, built at Wagle Estate, Thane. Our ASTM F392 flex durability tester shows whether a barrier film or laminate survives the twisting and creasing of converting, filling and transport.
What is the Gelbo flex test? A 200 × 280 mm specimen on two mandrels is twisted and crushed – 440° over the first 90 mm of stroke, then a 65 mm push – at 45 cycles per minute. What does a Gelbo flex tester measure? The damage. You then count pinholes (dye or coloured turpentine) or compare OTR with an unflexed control – a pinhole flex test for barrier films run on a flexible packaging film testing machine.
Pharma strip and blister packing depends on foil-laminate barrier integrity. How do you choose an ASTM F392 condition for a quick pharma foil laminate check? Your specification decides, and Conditions D and E give the quick check. In the pharma packaging barrier integrity testing equipment that plants in Andhra Pradesh assemble, the Gelbo supplies the flex conditioning step; the pinhole or OTR check is separate.
ASTM F392 conditions A to E explained: five conditions, set by cycle count.
| Condition | Flex type | Cycles | Time | Use case |
| A | Full flex (twist + crush) | 2,700 | 60 min | Most severe; clear-film seals can fail |
| B | Full flex | 900 | 20 min | Intermediate, per specification |
| C | Full flex | 270 | 6 min | Moderate; routine comparison |
| D | Full flex | 20 | about 27 s | Early-failure screen, e.g. delamination |
| E | Partial flex only | 20 | about 27 s | Gentlest, per specification |
How many cycles are in a Gelbo flex test? 2,700, 900, 270 or 20 full-flex cycles (A-D), or 20 partial (E). How long does a Gelbo flex test take? 60, 20 or 6 minutes of flexing for A-C, under half a minute for D or E, plus loading and the pinhole check. How many minutes does Condition B take? 20 minutes of flexing – 900 cycles at 45 per minute. Can a flex test detect early laminate delamination? Condition D, at 20 full-flex cycles, is the early-failure screen, for example for delamination.
Key technical data for the Gelbo flex tester supplied to packaging and laminate labs in Andhra Pradesh.
| Parameter | Specification |
| Testing Standard | ASTM F392 |
| Sample Dimensions | 200 mm × 280 mm (8 in × 11 in) |
| Twisting Frequency | 45 cycles per minute |
| Twisting Angle | 400° or 440° (model dependent) |
| Stroke / Compression Distance | 80 mm or 155 mm horizontal travel (model dependent) |
| Mandrel Diameter | 90 mm, stainless steel |
| Drive System / Motor | 1/2 HP, 1440 RPM gear motor with 45 rpm output, controlled by a Delta-make drive |
| Power Requirements | 230 V AC, 50 Hz |
| Dimensions (approx.) | 1000 mm (W) × 390 mm (D) × 340 mm (H) |
Twist angle and stroke vary by model. The 440° twist over the first 90 mm and the 65 mm push described earlier make up the 155 mm, 440° configuration.
Manufacturer, not a trader. A laboratory testing equipment manufacturer that labs in Andhra Pradesh deal with directly.
Full and partial flex. Every ASTM F392 flex durability tester we ship to Andhra Pradesh runs Conditions A to E.
NABL traceable, ISO 9001:2015. CE marked; direct factory supply.
One source for packaging QC lab equipment in Andhra Pradesh: add our humidity chamber and dart impact tester.
Direct dispatch from Thane since 2023. Packers in Visakhapatnam and Vijayawada buy from us directly; we dispatch from Thane with installation and AMC.
See the full specifications on our main Gelbo flex tester page. We also supply and install Gelbo flex testers in other states: Gelbo flex tester in Gujarat · Gelbo flex tester in Karnataka · Gelbo flex tester in Maharashtra · Gelbo flex tester in Tamil Nadu · Gelbo flex tester in Telangana.
| Product | Why Related |
Impact puncture of films (ASTM D1709) |
|
Film tensile (ASTM D882) and seal strength (ASTM F88) |
|
Conditioning specimens before flexing |
|
Cutting film strips for tensile testing |
|
Flex cracking of rubber (ASTM D430) |
|
Cut growth of rubber soles (ASTM D1052) |
|
Flex endurance of thin rubber components |
|
Drop testing of filled pouches and cartons |
|
Transport simulation of packed goods |
All Equipments & specimen preparation products can be customised as per requirements.