Finetech Engineering is a rectangle cutter manufacturer Telangana rubber and plastics testing labs rely on for accurate, repeatable rectangular specimen preparation. Every rectangle cutter we build is precision-ground and dimensionally verified against the governing specification before it leaves our Wagle Estate, Thane factory – manufacturer, not trader. A pharma packaging QC manager asking what is a rectangle specimen cutter used for usually already has the answer half-formed: whatever a round disc simply cannot cut, which in practice means custom compression blocks for closures and gaskets, plus general hardness strips.
A rectangle cutter for compression set is used specifically where a compression-set test rig calls for a rectangular block or slab specimen rather than the standard small circular disc – relevant for Telangana’s pharma packaging sector when qualifying larger rubber gasket or seal components tested in custom compression fixtures. For the standard small-button ASTM D395 disc specimen (29 mm or 13 mm diameter), Finetech’s Round Cutter remains the correct tool; the rectangle cutter addresses the rectangular-block configuration used in larger-scale or custom compression-set testing setups. Pharma closure teams asking how to cut rectangular compression set specimen blocks correctly should start from the fixture drawing supplied by the packaging line, not from the round disc dimensions used elsewhere in the same lab.
As a rectangle cutter supplier Hyderabad and rectangle cutter supplier Secunderabad testing labs have used since 2023, we supply rectangle cutters built to precise, repeatable block dimensions for compression-set fixtures, and to relevant plastics flexural and general strip-specimen standards where required. For rectangle cutter price Telangana enquiries, contact us with your exact specimen dimension requirement and we will confirm a quotation – every cutter is dispatched from our Thane factory with the exact blade geometry your application specifies. On rectangular specimen cutter Telangana cost, we have found the number genuinely depends on block size and tolerance rather than any list price – a quick fixture drawing gets you an accurate quote faster than a phone call alone.
Tip: Before ordering a rectangle cutter for compression-set testing, confirm your compression fixture’s exact specimen dimension requirement with your test engineer – unlike the standardised small-disc ASTM D395 specimen, rectangular block dimensions for larger custom compression rigs vary by fixture design and are not fixed by a single universal standard.
ASTM D395 specimen dimensions are defined primarily around circular disc specimens for the standard small-button compression set test, but Telangana labs working with larger pharma packaging or industrial rubber components should understand both configurations. There is a reason nobody can give a single answer to what size a rectangular compression set block for a pharma closure fixture should be: unlike the round disc, block dimensions are set by whoever designed the compression rig, not by ASTM D395 itself:
Configuration | Specimen Shape | Typical Dimensions | Cutter Used |
Standard small-button (Type 1) | Circular disc, stacked to thickness | 29 mm or 13 mm diameter discs, stacked to 12.5 ± 0.5 mm total thickness | Round Cutter |
O-ring compression set | Circular / annular | Per the O-ring’s actual cross-section dimensions | Round Cutter (custom sizing) |
Rectangular block (custom/larger fixtures) | Rectangular block or slab | Varies by compression fixture – confirm exact dimensions with your test rig specification | Rectangle Cutter |
The critical point in ASTM D395 specimen dimensions is that the standard, most widely referenced ASTM D395 test uses the circular disc configuration – if your specification simply cites “ASTM D395” without further detail, it most likely calls for the standard disc specimen and the Round Cutter. The rectangular block configuration is used specifically where a custom compression fixture, typically for larger pharma closures or gaskets, has been designed around a rectangular geometry instead. In practical terms, the difference between round cutter and rectangle cutter ASTM D395 specimens is simply which fixture your pharma customer built – one calls for the standard disc, the other for a block sized to their own closure or gasket geometry.
Note: Always confirm with your customer or test engineer which specimen geometry their compression set specification actually requires before ordering a cutter. Citing “ASTM D395” alone does not confirm rectangular block dimensions – the standard’s default and most common specimen is the circular disc.
Unlike compression set testing, Shore hardness testing (ASTM D2240) does not require a specific specimen shape – only adequate thickness (typically a minimum of 6 mm, achieved by stacking thinner sheets if needed) and enough flat surface area for the durometer’s indenter foot to seat properly. A rubber strip cutter for hardness test is therefore a genuinely accurate and common use for Finetech’s rectangle cutter: producing a flat rectangular strip specimen that gives Telangana rubber labs a consistent, adequately sized substrate for Shore A or Shore D hardness readings. Pharma QC teams frequently ask us can a rectangle cutter be used for hardness testing on incoming gasket compound, and the answer is straightforward – since Shore hardness sets no shape requirement, a rectangular strip is just as valid as any other flat, sufficiently thick piece.
Why rectangular strips work well for hardness testing: the durometer indenter only needs a flat, sufficiently thick area to seat – a rectangular strip cut to a consistent size gives a repeatable, easy-to-handle specimen for routine batch QC.
Typical use: incoming rubber compound batch QC for Telangana’s pharma packaging closures and general industrial rubber goods, where a quick hardness check on a rectangular strip gives a fast pass/fail read before committing the batch to production.
Complementary to other specimen types: many Telangana labs prepare a rectangular hardness strip alongside dumbbell tensile and round compression-set specimens from the same sheet, covering three tests from one moulded slab. A rectangular block specimen cutter rubber gasket manufacturers keep alongside their dumbbell and round cutters is what lets a Telangana pharma-packaging lab run tensile, compression set and hardness checks from a single incoming sheet.
Whether your lab is in Jeedimetla, Patancheru, IDA Nacharam or Secunderabad, as a rectangle specimen cutter manufacturer Hyderabad and laboratory equipment manufacturer Telangana plants have sourced from since 2023, we dispatch rectangle cutters directly from our Wagle Estate, Thane factory – including testing instruments Jeedimetla labs receive on scheduled delivery routes covering that cluster.
Standard | Specimen Configuration | Typical Dimensions | Application |
ASTM D395 (Type 1, standard) | Circular disc – Round Cutter | 29 mm or 13 mm diameter | Standard small-button compression set testing |
ASTM D395 (rectangular/custom) | Rectangular block – Rectangle Cutter | Fixture-specific, confirm before ordering | Larger pharma closure/gasket and industrial rubber compression testing |
ISO 815 (Type A, standard) | Circular disc – Round Cutter | 13 mm diameter, 6.3 mm thick (typical) | Standard ISO compression set testing |
ASTM D2240 (hardness) | Flat specimen, any shape – Rectangle Cutter suitable | Minimum ~6 mm thickness, adequate flat area | Shore A / Shore D hardness testing on incoming rubber compound |
Manufacturer, not a trader: Every rectangle cutter is designed, precision-ground and dimensionally verified at our Wagle Estate, Thane factory – not resold from another manufacturer.
ISO 9001 certified: Our manufacturing is ISO 9001:2015 certified and our equipment is CE marked.
NABL-traceable dimensional certification: Cutter dimensions verified and certified against the governing specification, supporting NABL-accredited lab audits and pharma regulatory documentation requirements.
Custom dimensions for compression fixtures: Since rectangular compression-set block dimensions vary by fixture design, we build cutters matched to your exact specification rather than a generic size. No compression set specimen cutter rectangular pharma closure fixtures require leaves our factory as a stock size – each one is ground against the customer’s own drawing before it ships.
Scheduled delivery across Telangana: Regular routes covering Jeedimetla, Patancheru, IDA Nacharam and Secunderabad from our Thane factory.
Re-sharpening and replacement support: We offer blade re-sharpening and replacement service to keep your cutter producing clean, repeatable specimen edges.
| Product | Why Related |
For dumbbell/dogbone tensile specimens (ASTM D412, D638) |
|
For tear strength testing (ASTM D624, ISO 34-1) |
|
Labs testing paper tensile strips also test burst strength |
|
Uses rubber strips cut by the strip cutter for compression set testing |
|
The machine that runs tensile tests on cut strip specimens |
|
Drives the rectangular die cutter through sheet material |
|
For moulding rubber sheets from which strips are cut |
Tell us your application (compression-set block, hardness strip, or plastics flexural specimen), the exact dimensions your test fixture or standard requires, and your location in Telangana. For rectangle cutter price Telangana enquiries, we will confirm your exact specimen requirement first, then send a quotation – no invented figures, no generic pricing.
WhatsApp: +91 93241 37971 (click-to-chat)
Phone: +91 93241 37971 (click-to-call)
Factory & dispatch: C-1 New Kalwa Industrial Premises, Wagle Estate, Thane (W) 400604
All Equipments & specimen preparation products can be customised as per requirements.
A rectangle cutter for compression set is used when a compression-set test rig calls for a rectangular block or slab specimen rather than the standard small circular disc - relevant for Telangana's pharma packaging sector qualifying larger rubber closures and gaskets in custom compression fixtures. For the standard ASTM D395 small-button disc specimen (29 mm or 13 mm diameter), a Round Cutter is the correct tool; the rectangle cutter addresses the rectangular-block configuration specifically. Buyers new to this often ask is rectangle cutter different from round cutter across the board. Not entirely - for hardness strips either does the job, but for compression set work the two prepare specimens for genuinely different fixture geometries.
ASTM D395 specimen dimensions for the standard Type 1 test are circular discs, either 29 mm or 13 mm in diameter, stacked to a total thickness of 12.5 ± 0.5 mm. This is the default, most commonly referenced configuration when a specification simply cites 'ASTM D395.' Rectangular block specimens are used only in custom compression fixtures designed around that geometry - confirm which configuration your test rig requires before ordering a cutter.
Yes. A rubber strip cutter for hardness test preparation is a genuinely accurate use of the rectangle cutter - Shore hardness testing (ASTM D2240) does not require a specific specimen shape, only adequate thickness (typically a minimum of 6 mm) and sufficient flat area for the durometer's indenter foot to seat. A rectangular strip cut to a consistent size gives Telangana rubber labs a repeatable, easy-to-handle specimen for routine incoming-compound hardness QC.
We are a manufacturer. As a rectangle specimen cutter manufacturer Telangana and rectangle specimen cutter manufacturer India testing labs have used since 2023, every cutter is designed, precision-ground and dimensionally verified in-house at our Wagle Estate, Thane facility - not purchased from another manufacturer and resold.
Yes. We are a rectangle cutter supplier Hyderabad and rectangle cutter supplier Secunderabad labs have sourced from directly, alongside Jeedimetla, Patancheru and IDA Nacharam. Dispatch is from our Wagle Estate, Thane factory, with scheduled delivery routes covering Telangana's testing-lab corridor.
